Cannabis needs 70–80% relative humidity during germination, 50–70% in the vegetative stage, 40–50% in flowering and 30–40% in the last weeks before harvest. If humidity stays too high in flowering, mould and bud rot threaten the dense flowers. The values apply to plants grown from seeds and from clones.
What humidity does cannabis need at each stage?
Humidity drops with every stage: young plants also take up water through their leaves, while flowering plants with dense buds tolerate humid air badly. The table shows guide values from breeder information from Linda Seeds (in German).
| Stage | Relative humidity | Temperature (lights on) |
|---|---|---|
| Germination and clones | 70–80% | 22–25 °C |
| Vegetative | 50–70% | 22–28 °C |
| Flowering | 40–50% | 20–26 °C |
| Late flowering | 30–40% | as in flowering |
It can be slightly cooler in the tent at night. The values are guides, not guarantees: variety, substrate and ventilation shift the optimum a little. Look at the plant, not just the display: curled or burnt leaf tips and damp buds are early warning signs. You will find more on the sequence of stages in the article on growth stages.
Why is humid air a problem in flowering?
Humid air favours grey mould (Botrytis), which destroys dense buds from the inside. The Utah State University Extension names humidity and cool temperatures as conditions for Botrytis and recommends keeping relative humidity in a greenhouse below 50%. Infected buds cannot be saved, so prevention is what counts.
Air that is too dry is also unhelpful. The plant then loses a lot of water through its leaves, partly closes its stomata and grows more slowly. You will find more on the fungus and its signs in the article Botrytis in cannabis.
What is VPD and do I need it?
VPD (vapour pressure deficit) combines temperature and humidity in a single number, measured in kilopascals (kPa). You do not need it to grow well, but it helps with fine-tuning. According to a Michigan State University extension column, a VPD of 0.7 to 1.5 kPa counts as the target range for most plants. Below 0.3 kPa water transport slows and leaves stay wet; above 1.5 kPa the plant loses water very quickly. The figure comes from greenhouse growing in general and does not mention cannabis. Use it as a guide, not a rule.
How do I regulate humidity step by step?
With a meter, a fan and, if needed, a humidifier or dehumidifier. Here is how:
- Hang a thermo-hygrometer at the height of the plant tops, not on the tent wall.
- Read the value with the lights on and with the lights off, and note it for a few days.
- If the air is too humid, increase the extraction and aim a fan under the canopy. A dehumidifier is best placed outside the tent so it does not heat the space further.
- If the air is too dry, set up a humidifier in the cold months.
- Lower the value at the start of flowering in small steps over several weeks instead of changing it abruptly. Blimburn Seeds (in German) describes this gradual reduction from about 50–60% in the first weeks of flowering to 40–50% in mid-flowering.
For temperatures in the tent, see the article on grow lights, because lamps determine the heat in the room.
Common humidity mistakes
- One fixed value for all stages. Result: young plants dry out or flowers sit in air that is too humid. Fix: lower the value with each stage.
- Flowering air too humid. Result: mould in dense buds, often visible only late. Fix: stay below 50% in flowering and check the buds regularly.
- No air movement. Result: moisture builds up locally even though the room average is right. Fix: a fan that moves the air under the canopy.
- Guessing instead of measuring. Result: deviations are noticed too late. Fix: a hygrometer, ideally a second one as a cross-check.
- Abrupt changes. Result: stress for the plant. Fix: adjust the value only in small steps per week.
FAQ
What humidity is ideal in flowering?
In flowering the guide value is 40–50% relative humidity. In the last weeks before harvest, 30–40% is usual to prevent mould in the dense, ripe buds.
What humidity do seedlings and clones need?
At 70–80% relative humidity, seedlings and clones need the most humid air of the whole cycle, at 22–25 °C. As the roots grow, you lower the value gradually to 50–70%.
What happens if humidity is too high?
If humidity is too high, the risk of moulds such as Botrytis rises, especially in flowering. An infection cannot be cured, so you remove affected plants quickly. Good air movement and enough space between plants help prevent it.
Where do I measure humidity in the tent?
Measure at the height of the plant tops, not on the tent wall or near the floor. The values there usually differ from those around the leaves. A second device in another spot shows whether moisture is building up locally.
Do I need a dehumidifier?
Not always. If extraction and fans keep flowering below 50%, you do not need one. In cool, damp months or in small rooms without air exchange, a dehumidifier can make sense.
Sources
- Guide values for humidity and temperature by stage (germination, vegetative, flowering, late flowering): Linda Seeds, breeder information (German)
- Late flowering at 30–40%, gradual reduction, Botrytis risk: Blimburn Seeds, breeder information (German)
- Botrytis needs moisture, keep greenhouses below 50%, no fungicide available: Utah State University Extension, Hemp Bud Rot
- Definition and target range of VPD: Michigan State University, Water Vapor-Pressure Deficit
Note: this article is for general information about plant cultivation only. Please observe the laws on growing and possessing cannabis that apply in your country or canton.